Most newer cars have changed the traditional key-style ignition switch with a Start Engine Push Button system. A Smart Fob sends a coded security signal to the Powertrain Control Module (PCM) via the cars’s keyless entry system when the fob is inside the car. This informs the PCM that the engine can be started at any time.
Before the engine will be ignited, the transmission must be in Park or Neutral, and the driver must depress and hold the brake pedal. Pushing in the Start Engine Button sends a command to the PCM. The PCM then checks the status of the Park/Neutral Safety switch and the Brake Pedal Switch. If the transmission is in Park or Neutral, and the brake is on, the PCM then sends a start command to the starter motor to crank the engine.
NOTHING HAPPENS WHEN YOU PUSH THE START ENGINE BUTTON
If the engine does not crank when you press the Start Engine button, any of the following may be keeping the engine from starting:
Dead Battery inside Smart Key FobDead Battery inside Smart Key Fob
What to do: Hold the dead key fob against the start button, then use the fob to press the Start Engine button down. This should allow the button to inductively read the security code in the fob and pass the start command to the PCM. Your engine should start then.
Change the dead battery inside the Smart Fob with a new battery as soon as possible.
Wrong Key Fob or Defective Key Fob
If you accidentally picked up the wrong key fob for your car, or the fob itself is defective, your engine will NOT start.
What To Do: Have your car towed to your car dealer to have a new fob programmed for your cars, or call a certified locksmith who can change and program a new key fob.
Defective Start Engine Button
You have the correct key fob and the battery inside the fob is good, but nothing happens when you press the Start Engine Button or use the fob to press the Start Button.
What To Do: change the defective Start Engine Button with a new one.
Car Battery is Dead
A dead or discharged car battery can keep your engine from cranking or starting.
What To Do: Open the hood and check battery voltage with a volt meter. A battery that has more than about 12.4 volts should have enough voltage to start the engine. If the battery is low or dead, try jump starting the battery from another car, or hook up a battery charger to recharge or boost the battery. Also, inspect the battery cable connections to ensure they are clean and tight. Have your battery tested to know its condition. If it is more than 4 or 5 years old, chances are you require a new battery.
If the PCM has an internal fault, or there is an issue with the anti-theft system (such as not reading the fob correctly or the security codes have gotten out of sync), further diagnosis will be necessary to know the problem. There may a programming issue, or a fault in the keyless entry system or keyless entry module that routes the security signal to the PCM.
What To Do: This type of diagnosis is beyond the skill level of most do-it-yourselfers and needs a professional grade scan tool with bi-directional and reprogramming capability.
If the starter motor, or the relay, module or solenoid that energizes the starter is bad, the starter will not crank the engine.
What To Do: Attempt jumping the starter directly to see if it cranks the engine. This will tell you if the starter is working. The starter can also be removed and taken to an auto parts store that has a starter tester. If the starter tests bad, you need a new starter. If it tests good, the problem is not the start but likely a bad starter module, relay or solenoid. Be sure to check all the cables and wires that connects to the starter. Loose, corroded or damaged wire connections can keep a good starter from cranking. So can a low battery.
Also, a damaged starter drive gear or missing or broken teeth on the engine’s flywheel may stop the starter from cranking the engine.
What To Do: Find the Power Center under the hood and check for blown fuses in the starter circuit. Change as needed (always change with same amp capacity fuse).
Engine Cranks But Will Not Start
The issue is NOT the Start Engine Push Button but something else that is not the engine from getting spark, fuel or compression. This will need further diagnosis to know the fault. Most likely causes are:
Dead and faulty Fuel Pump (or bad fuel pump relay)
Empty Fuel Tank (or fuel contaminated with water)
Bad or Faulty Crank Position Sensor
Broken Timing Belt (no Compression)